Certification Tests
Cisco CCNP / BSCI Exam Tutorial: Using OSPF's "Summary-Address" Command
BSCI exam success, not to mention earning your CCNP, can come down to your OSPF route summarization skills. There are a few different commands and situations you need to be ready for, and one of these situations is the proper use of the "summary-address" command.
The summary-address command should be used on an ASBR in order to summarize routes that are being injected into the OSPF domain via redistribution. In the following example, four routes are being redistributed into OSPF on R1, making R1 an ASBR.
interface Loopback16
ip address 16.16.16.16 255.0.0.0
!
interface Loopback17
ip address 17.17.17.17 255.0.0.0
!
interface Loopback18
ip address 18.18.18.18 255.0.0.0
!
interface Loopback19
ip address 19.19.19.19 255.0.0.0
R1(config)#router ospf 1
R1(config-router)#redistribute connected subnets
These four routes are seen on downstream router R2 as External Type-2, the default for routes redistributed into OSPF.
R2#show ip route ospf
O E2 17.0.0.0/8 [110/20] via 172.12.123.1, 00:00:07, Serial0
O E2 16.0.0.0/8 [110/20] via 172.12.123.1, 00:00:07, Serial0
O E2 19.0.0.0/8 [110/20] via 172.12.123.1, 00:00:07, Serial0
O E2 18.0.0.0/8 [110/20] via 172.12.123.1, 00:00:07, Serial0
To summarize networks learned by redistribution, use the OSPF command summary-address. You can probably do this summarization in your head, but do so before continuing with the lab.
R1(config)#router ospf 1
R1(config-router)#summary-address 16.0.0.0 252.0.0.0
Look at the change in R2's OSPF table.
R2#show ip route ospf
O E2 16.0.0.0/6 [110/20] via 172.12.123.1, 00:00:05, Serial0
The external routes have been successfully summarized. Note that the summary route is still marked as an E2 route.
There's an interesting route installed into R1's OSPF table as well.
R1#show ip route ospf
O 16.0.0.0/6 is a summary, 00:01:51, Null0
When you configure summary routes in OSPF, a route to null0 will be installed into the OSPF routing table. This helps to prevent routing loops. Any packets destined for the routes that have been summarized will have a longer match in the routing table....
C 17.0.0.0/8 is directly connected, Loopback17
C 16.0.0.0/8 is directly connected, Loopback16
C 19.0.0.0/8 is directly connected, Loopback19
C 18.0.0.0/8 is directly connected, Loopback18
O 16.0.0.0/6 is a summary, 00:03:10, Null0
O 12.0.0.0/6 is a summary, 00:07:53, Null0
.. and packets that do not match one of the summarized routes but do match the summary route will be dropped.
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials! Pass the BSCI exam with Chris Bryant!
Chris Bryant
Similar articles
Cisco CCNP / BCMSN Exam Tutorial: The Core Layer Of Cisco's Three-Layer Model
In this section, you're going to be reintroduced to a networking model you first saw in your CCNA studies. No, it's not the OSI model or the TCP/IP model - it's the Cisco Three-Layer Hierarchical Model. Read more →Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
When you're studying to pass the BSCI exam and earn your CCNP certification, you're going to be introduced to ISIS. ISIS and OSPF are both link-state protocols, but ISIS works quite differently from OSPF. Read more →Cisco CCNP / BSCI Exam Tutorial: Route Summarization
Preparing to pass the BSCI exam and earn your Cisco CCNP? Route summarization is just one of the many skills you'll have to master in order to earn your CCNP. Read more →Cisco CCNP Certification / BSCI Exam Tutorial: Route Summarization Basics
As you earn your CCNA and CCNP certification, you're going to have to get comfortable with manually summarizing routes. This isn't just another reason to learn binary math (although it's a good one! Read more →Aphorism
There are three roads to ruin; women, gambling and technicians. The most pleasant is with women, the quickest is with gambling, but the surest is with technicians.