Certification Tests
Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results
Your BCMSN and CCNP studies will include mastering the details of Spanning Tree Protocol (STP). While you learned some of these details in your CCNA studies, quite a bit of it may be new to you. Before going on to the intermediate and advanced STP features, let's review the root bridge election process and learn how to change these results.
Each switch will have a Bridge ID Priority value, more commonly referred to as a BID. This BID is a combination of a default priority value and the switch's MAC address, with the priority value listed first. For example, if a Cisco switch has the default priority value of 32,768 and a MAC address of 11-22-33-44-55-66, the BID would be 32768:11-22-33-44-55-66. Therefore, if the switch priority is left at the default, the MAC address is the deciding factor.
Switches are a lot like people - when they first arrive, they announce that they are the center of the universe! Unlike some people, the switches will soon get over it. BPDUs will be exchanged until one switch is elected Root Bridge, and it's the switch with the lowest BPDU that will end up being the Root Bridge.
If STP is left totally alone, a single switch is going to be the root bridge for every single VLAN in your network. Worse, that single switch is going to be selected because it has a lower MAC address than every other switch, which isn't exactly the criteria you want to use to select a single root bridge.
The time will definitely come when you want to determine a particular switch to be the root bridge for your VLANs, or when you will want to spread the root bridge workload. For instance, if you have 50 VLANs and five switches, you may want each switch to act as the root bridge for 10 VLANs each. You can make this happen with the spanning-tree vlan root command.
SW1(config)#spanning-tree vlan 1 ?
forward-time Set the forward delay for the spanning tree
hello-time Set the hello interval for the spanning tree
max-age Set the max age interval for the spanning tree
priority Set the bridge priority for the spanning tree
root Configure switch as root
In this example, we've got two switches, and SW1 has been elected the root bridge for VLANs 10, 20, and 30. We'll use the spanning-tree vlan root command on SW2 to make it the root bridge for VLANs 20 and 30.
SW2(config)#spanning-tree vlan 20 root primary
SW2(config)#spanning-tree vlan 30 root primary
SW2#show spanning vlan 20
VLAN0020
Spanning tree enabled protocol ieee
Root ID Priority 24596
Address 000f.90e2.1300
This bridge is the root
SW2#show spanning vlan 30
VLAN0030
Spanning tree enabled protocol ieee
Root ID Priority 24606
Address 000f.90e2.1300
This bridge is the root
SW 2 is now the root bridge for both VLAN 20 and 30. Notice that the priority value has changed from the default of 32768.
In the next CCNP / BCMSN tutorial, we'll take a look at more STP features.
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. For a FREE copy of his latest e-books, ?How To Pass The CCNA? and ?How To Pass The CCNP?, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Pass the CCNP exam with The Bryant Advantage!
Chris Bryant
Similar articles
Cisco CCNA Exam Tutorial: IGRP And Equal Cost Load Balancing
To pass the CCNA exam, you've got to know the role of the bandwidth command with IGRP and EIGRP and when to use it. In this tutorial, we'll configure IGRP over a frame relay hub-and-spoke network using the following networks:R1 (the hub), R2, and R3 are running IGRP over the 172. Read more →Cisco CCNP / BSCI Exam Tutorial: 10 ISIS Details You Must Know!
Earning your CCNP certification and passing the BSCI exam depends on knowing the details of many Cisco technologies, ISIS chief among them. To help you prepare for exam success, here's a list of ISIS terminology and basic concepts that will help you pass this tough exam. Read more →Cisco CCNP / BSCI Certification: Introduction To ISIS Terminology
When you're studying to pass the BSCI exam and earn your CCNP certification, you're going to be introduced to ISIS. ISIS and OSPF are both link-state protocols, but ISIS works quite differently from OSPF. Read more →Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review
OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. Read more →Aphorism
Men are only as good as their technical development allows them to be.