Certification Tests
Cisco CCNA Exam Tutorial: Troubleshooting Directly Connected Serial Interfaces
CCNA exam success depends largely on noticing the details, and this is especially true of configurations involving directly connected serial interfaces. And of course, it's not enough to notice these details - you've got to know what to do about them!
A Cisco router is a DTE by default, but directly connecting two DTEs with a DCE/DTE cable is not enough. In the following example, R1 and R3 are directly connected at their Serial1 interfaces. The line goes up briefly after being opened, but the line protocol goes down after about 30 seconds.
R3(config-if)#int s1
R3(config-if)#ip address 172.12.13.3 255.255.255.0
R3(config-if)#no shutdown
2d18h: %LINK-3-UPDOWN: Interface Serial1, changed state to up
2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
R3(config-if)#
2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
The problem is that one of the routers needs to act as the DCE in order for the line protocol to come up and stay up. If this were your CCNA / CCNP home lab, you could just go over and look at the DTE/DCE cable to see which router had the DCE end of the cable attached. In this example, though, we don't have physical access to the routers. How can we tell which router has the DCE end of the cable attached?
R3#show controller serial 1
HD unit 1, idb = 0x1C44E8, driver structure at 0x1CBAC8
buffer size 1524 HD unit 1, V.35 DCE cable
The show controller command gives us this information. (There's a lot more output that this with this command, but it's unimportant for our purposes.) The router with the DCE end of the cable needs to supply a clock rate to the DTE, and we'll do just that with the interface-level clockrate command.
R3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#int serial1
R3(config-if)#clockrate 56000
2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
In just a few seconds, the line protocol goes up and stays up.
When troubleshooting a connection, always run show interface first. If you see the combination shown below, the connection is physically fine but logically down. That's generally the result of a needed keepalive not being present. With Frame Relay, it's probably an LMI issue, but with directly connected serial interfaces the issue is most likely the DCE end of the connection not supplying clockrate.
R3#show interface serial 1
Serial1 is up, line protocol is down
Troubleshooting is a big part of the job, and it's a big part of the Cisco CCNA and CCNP programs as well. Know your show and debug commands and you're on your way to passing the CCNA!
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
For a FREE copy of his latest e-books, ?How To Pass The CCNA? and ?How To Pass The CCNP?, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide with The Bryant Advantage!
Chris Bryant
Similar articles
Cisco CCNA Certification: How And Why Switches Trunk
Your CCNA studies are going to include quite a bit of information about switches, and for good reason. if you don't understand basic switching theory, you can't configure and troubleshoot Cisco switches, either on the CCNA exam or in the real world. Read more →Cisco CCNA Exam Tutorial And Case Study: VLANs and IP Connectivity
In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). Read more →Cisco CCNP / BSCI Exam Tutorial: 10 ISIS Details You Must Know!
Earning your CCNP certification and passing the BSCI exam depends on knowing the details of many Cisco technologies, ISIS chief among them. To help you prepare for exam success, here's a list of ISIS terminology and basic concepts that will help you pass this tough exam. Read more →Cisco CCNP / BCMSN Exam Tutorial: The Core Layer Of Cisco's Three-Layer Model
In this section, you're going to be reintroduced to a networking model you first saw in your CCNA studies. No, it's not the OSI model or the TCP/IP model - it's the Cisco Three-Layer Hierarchical Model. Read more →Aphorism
By his very success in inventing labor-saving devices, modern man has manufactured an abyss of boredom that only the privileged classes in earlier civilizations have ever fathomed.